| Subject | Author | Year |
| AGMA/API/ISO | | |
| An API Service Factor is not the same as an AGMA Service Factor | J. Amendola/Artec Machine Systems | 2005 |
| BEARINGS | | |
| Shaft Bearing Clearances for Radial Hydrodynamic Bearings – A General Guideline | J. Amendola | 2010 |
| What is Bearing Pre-load? | J. Amendola | 2010 |
| Tilting Pad Journal Bearings with Spray-Bar Blockers and Bypass Cooling for High Speed, High Load Applications | J. Nicholas | 2003 |
| Improved Bearing Alloy- A Contribution Toward Environmental Protection | Rolf Koring | 2003 |
| No Bearing Problems | Kiesel/Holland | 2000 |
| Tilting Pad thrust Bearings: Factors affecting Performance and Improvements with Directed Lubrication | M.K. Bielec/A.J. Leopard | 1970 |
| * White Metal Bearings - Basic Parameters | J. Amendola/Artec Machine | 2006 |
| * High Speed Radial Bearings for use with Renk-Maag Turbogears | J. Amendola/Artec Machine | 1994 |
| * Standard Method Calculation for the Sizing of Thrust Bearings | C. Buergin/J. Amendola | 2002 |
| * Behavior of a Tilting Pad Thrust Bearing During Start-Up | R.E. Gustafson | 1967 |
| *Bearings for High Speed Gears | K. Novak/Maag Gear-Wheel Co. Ltd. | 1987 |
| COMMISSIONING/MAINTENANCE/ASSEMBLY OF GEARBOXES | | |
| The importance of Static and Dynamic tooth contact checks in Single and Double Helical Gears | J. Amendola/Artec Machine | 2005 |
| * Shimming of Gearboxes on its Respective Foundation Base Plate | J. Amendola/Artec Machine | 2002 |
| * General Turbo-Gear Inspection/Commissioning Checks of a Rotor Set relating to Gear Toothing | J. Amendola/Artec Machine | 2005 |
| * Tooth Contact Field Adjustments of Highly Loaded High Speed Turbogears | J. Amendola/Artec Machine | 2005 |
| *Gear Assembly, Installation and Maintenance | H. Davatz/Maag Gear-Wheel Co. Ltd. | 1987 |
| COUPLINGS | | |
| Application of Flexible Couplings for Turbomachinery | Kopflex/Lucas Aerospace | 1989 |
| Integral Flanges for Gear Rotors | J. Amendola/Artec Machine | 2003 |
| Gear Couplings | D.E. Rocker/ASME | 1967 |
| What are the Differences in High Performance Flexible Couplings for Turbomachinery? | J. Mancuso J. Corcoran | 2003 |
| Toothed Couplings | O. Stadeli/Maag Gear-Wheel Co. Ltd. | 1987 |
| Extend Gear Coupling Life | M. Calistrat | 1978 |
| What Causes wear in Gear Type Couplings | M. Calistrat | 1975 |
| A Special Grease for Flexible Shaft Couplings | M. Calistrat | 1981 |
| Grease Separation under Centrifugal Forces | M. Calistrat | 1981 |
| Tooth Coupling Floating Member Diagrams | MAAG Gear-Wheel Co. Ltd. | |
| Hydraulic Removal and Installation Coupling Hubs - Keyed and Keyless | M. Calistrat, J. Morris, R. Parker | 1995 |
| *The development of Euroflex Transmissions Ltd. | R. Goody/Euroflex Transmissions | 2005 |
| *Answers to Frequently Asked questions on Euroflex Couplings | R. Goody/Euroflex Transmissions | 2005 |
| *New Low Weight Dry Couplings | T. Deeg/Maag | 1995 |
| COUPLINGS - SYNCHRONOUS CLUTCH | | |
| Design & Application of MAAG Synchronous Clutch Couplings: Types MS & HS | O. Stadeli/Maag Gear edited: by Artec | 2009 |
| Design & Function of MAAG Synchronous Clutch Couplings: Types MS, HS & DS | O. Stadeli/Maag Gear-Wheel Co. Ltd. | |
| *US Naval Ship Engineering Evaluation of the MAAG Synchronizing Clutch Coupling - NAVSECPHILADIV PROJECT T-789 | NAVSEC Philadelphia Division | 1971 |
| EFFICIENCY OF GEARBOXES | | |
| HET Gear Design to Improve Power Plant Efficiency | U. Giger/Maag | 2000 |
| Efficiency Test on a Large slow speed Planetary Gear | W.Nageli & W.Ackle/Maag Gear-Wheel Co. Ltd. | 1986 |
| High Efficiency Turbogears for Gas Turbines | T. Deeg/Maag | 1996 |
| High Efficiency Turbogears for Gas Turbines - First Operating Experiences | A. Mathis/R. Losch-Schloms | 1998 |
| * Understanding the Thermal Rating of Gearboxes | J. Amendola/Artec Machine | 2000 |
| EPICYCLIC GEARBOXES | | |
| Epicyclic Gearing - An Overview | www.marineengineering.org.uk | |
| Turbo Planetary Gear Units: State of the Technology | A. Thuswaldner/Maag | 2003 |
| * Advantages of an Epicyclic Gear | J. Amendola/Artec Machine | 1994 |
| FRICTION - CLUTCHES | | |
| Friction Clutches - An Overview | www.marineengineering.org.uk | |
| GEARBOX TYPES - TURBO | | |
| Experience with Special Applications | R. Schoch/Maag Gear-Wheel Co. Ltd. | 1987 |
| Gear Thrust Collars & Solid Couplings | | 1969 |
| Gear Drives for Turbo machinery | P. Lynwander/American Lohmann | |
| Design Features of the Standard Gear Series | M. Buechel/Maag Gear-Wheel Co. Ltd. | 1987 |
| 65 MW Gearboxes to generate power for German Railway | T. Deeg/Maag Gear-Wheel Co. Ltd. | 1996 |
| The Outlook on Future Design of Turbo Gearing | Hans Sigg/Maag Gear-Wheel Co. Ltd. | 1985 |
| * General Statement Regarding the Maag "GB" and "GN" Series Gearboxes | J. Amendola/Artec Machine | |
| GEARBOX TYPES - MARINE | | |
| Marine Gear Layouts | www.marineengineering.org.uk | |
| Marine gearing-Development & Technology | H. Sigg/Maag Gear-Wheel Co. Ltd. | 1989 |
| New Development of the MPV-59 double stage planetary gearbox for the LM-2500 plus | J. Duenki/Maag | 2003 |
| HEAT TREATMENT | | |
| * Material, Heat Treatment and its Quality Control for Turbo Gears | Dr. P. Brezina/Maag Gear-Wheel Co. Ltd. | 1987 |
| * 65 Years Experience with Case Hardened & Ground High Speed Gearing | H. Sigg/Maag Gear-Wheel Co. Ltd. | 1987 |
| * Influence of Hardened and Ground Gears on systems Designs | H. Sigg/Maag Gear-Wheel Co. Ltd. | 1965 |
| * Drip feed Carburizing | U Wyss/Maag Gear-Wheel Co. Ltd. | 1978 |
| * Gear Materials and Heat Treatment | U. Wyss/Maag Gear-Wheel Co. Ltd. | 1984 |
| * Effects of Material Defects on Gear Performance - A Case Study | R. Drago | 1999 |
| * Gas Carburizing by the Drip Feed method in Switzerland | Urs Wyss/Maag Gear-Wheel Co. Ltd. | 1963 |
| INSTRUMENTATION OF GEARBOXES | | |
| *Casing Accelerometers - Typical Set point Values | | 2002 |
| * Possibilities of Install./Vibration Probes & Thermocouples | Buechel/Bertschinger |
| LUBRICATION OF GEARS | | |
| Gear Lubrication Relating Theory to Practice | Fowle | 1976 |
| The effect of a ZnDTP anti-wear additive on the micropitting resistance of carburized steel rollers | C Benyajati & A V Olver | 2004 |
| What's So Special about Specialty Lubricants? | Machine Design | 1985 |
| Characteristics of Regimes of Gear Lubrication | Darle Dudley | 1981 |
| Lubrication Effects on Surface Pitting and Scuffing in Gears - A Review | H. S. Cheng | 1999 |
| The Role of Viscosity in Lubrication | AMSE | 1960 |
| Lubrication of Gears | Texaco | 1961 |
| * The influence of EP additives in light turbine oils used in High Speed High Power Turbogears | J. Amendola/Artec Machine | 1999 |
| * Comparison oil pressure to oil flow quantity in Turbogears | J. Amendola/Artec Machine | 1994 |
| * Direct observations of a micropit in an elasto-hydrodynamic contact | A. V. Olver, L.K. Tiew, S. Medina, J.W. Choo | 2003 |
| MANUFACTURING TECHNIQUES | | |
| * Calculation of Thrust Collar Requirements | C. Buergin/Maag | 2003 |
| *Gear Tooth Grinding Steps | Gear Tech | 1993 |
| * Metrological Inspection of Gears | E. Guenter/Maag | 1978 |
| * Grinding Shaving cutters & Rolling Dies by CBN Wheels | E. Guenter/Maag | |
| * Examples of Modern Gear Measuring Technology | E. Guenter/Maag | |
| * Maag Gear Grinding Methods | E.Gunter&A.Rust/Maag | |
| * Gear-Cutting, Grinding & Measuring Methods | E. Guenter/Maag Gear | |
| MATERIALS (Rotor Steels) | | |
| * List of Raw Materials for Gears - Cross Reference List | Artec Machine | 2000 |
| MILL DRIVES | | |
| 3-Stage-Planetary Gearbox For Vertical Roller Mills | Dr. R. Raeber, U. Weller, R. Amato/Maag | 2006 |
| Central Drive or Girth Drive for Ball Mills | W. Ackle/Maag Gear-Wheel Co. Ltd. | |
| MOTORS | | |
| LCI's and Synchronous Motors | J. Zayechek | 2000 |
| Ball Mill Drive Motor Choices | J. Green/J. Stoker | 2000 |
| NOISE OF GEARS | | |
| * Gearbox noise | J. Amendola/Artec Machine | 2003 |
| * Relative Noise Levels of Parallel Axis Gear Sets with Various Contact Ratios and Gear tooth Forms | R. Drago/R.H. Spencer/M. Lewis/F. Oswald | 1993 |
| * Gear Noise - The Generation of Rotational Harmonic Frequencies in Marine Propulsion Gears | G. W. Nagorny R. A. Stuchfield | 1981 |
| * The Ultra Low Noise Gearbox | Institute of Marine Engineers | 2000 |
| * Determination of Airborne Sound Power Levels Emitted by Gear Units | ISO/DIS 8579/1 | |
| * Silent Ship Propulsion Gear Systems | Dr. F. Hoppe/Maag Gear-Wheel Co. Ltd | |
| * Acoustics - Estimate of Airborne Noise by Machinery | ISO/Tech. report | 1987 |
| * Noise Control/Properties of Noise - Definitions/Explanation/Measurement | Environmental Eng. | 1992 |
| PUMPS - FOR LUBE OIL | | |
| When to Use a Positive Displacement Pump | | 2003 |
| TESTING OF GEARBOXES | | |
| Base Pitch Tables | W. Janninock | 1992 |
| * Statements Regarding Full Load Back-to-Back Locked Torque Testing | D. Martin/Artec Machine | 2001 |
| * Break Away Torque Calculations For 2 Rotor Shafts | J. Amendola/Artec Machine | 2003 |
| TOOTHING DESIGN | | |
| Single vs. Double Helical Gears | J. Amendola/Artec Machine | 2006 |
| Scuffing and Micropitting - Special Considerations | J. Amendola/Artec Machine | 2006 |
| Gear Design Principles | Dr. P. Bloch/Maag Gear-Wheel Co. Ltd. | |
| High Speed Gear - Modern Developments | T. Deeg/Maag | 1992 |
| * Deformation of Gear Teeth and Rotors | J. Amendola/Artec Machine | 2006 |
| * Lead correction derivation method for high capacity Turbo-Gears with high pitch line velocities - Thermal Influence | J. Amendola/Artec Machine | 2008 |
| * A Procedure For Predicting the Load Distribution and Transmission Error Characteristics of Double Helical Gears | T. Jacob/T. Houser | 1995 |
| * Illustrative Views of Gear Tooth Lead and Profile Modifications | J. Amendola/Artec Machine | 2001 |
| * Notes on Copper plating of gear toothing | J. Amendola/Artec Machine | 2003 |
| * Clarification on WR2 values | J. Amendola/Artec Machine | 2005 |
| * Calculation of Scoring Resistance in Gear Drives | R. Wydler/Maag Gear-Wheel Ltd. Co. | |
| * Gear Toothing | W.Nageli/Maag Gear-Wheel Co. Ltd. | 1987 |
| * Single or Double Helical Gears, Which is Better? | J. Amendola/Artec Machine | 2006 |
| * Calculation of Load Capacity of Gear Teeth | H. Sigg/Maag | |
| * Thermal Behavior of High-Speed Gears.&Tooth Correction for Gears | | 1972 |
| * Profile and Longitudinal Corrections on Involute Gears | Hans Sigg/Maag Gear-Wheel Co. Ltd. | 1965 |
| * Thermal instability in high speed gearing | W.P.Welch | 1961 |
| VIBRATIONS | | |
| Benefits of Implementing a Basic Vibration Analysis Program for Power Transmission Drives | S. Rogan/Artec Machine | 2009 |
| * Why do some Turbogears show higher than Normal Vibration Levels during Start-up | J. Amendola/Artec Machine | 2003 |
| * Synchronous Thermal Instability Prediction For Overhung Rotors (Morton Effect) | R. Gordon Kirk Z. Guo A. Balbahadur | 2003 |
| * Lateral & Torsional Vibrations | | |
| * Gear Vibrations | M. Steiner/Maag Gear-Wheel Co. Ltd. | 1987 |
| * Dynamic Rotor Stability in Duel Mode Turbogears - FCCU Drive Applications | J. Amendola/Artec Machine | 1978 |
| * Illustrated Vibration Diagnostic Chart | Charlotte | 1994 |
| * Tuning Out Torsional Vibrations | M. Corbo/S. Malanoski | |
| * Practical Design Against Torsional Vibrations | M. Corbo/S. Malanoski | 1996 |
| | | |
Technical papers on gearboxes
